By clicking “Accept All Cookies”, you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts. View our Privacy Policy for more information.
Specialist seating

Assessing for the correct chair size

In this blog, we stress the importance of choosing the right chair size for comfort and safety, offering practical guidance for assessment.
Subscribe to our newsletter
Share

Introduction

Having the correct size chair is essential and should be the second priority after considering how a person will transfer i.e. get in and out of the recommended chair. The correct size chair supports a person by reducing the need to shuffle around in the seat of the chair and the tendency to lean to one side to obtain support, and it enables users to stay in a midline position.

This not only enhances comfort, reduces the risk of pressure areas developing and enables both safer and easier transfers, but it also lessens the need for frequent repositioning and can aid circulation, digestion and respiration.

Seat depth and height

Ideally, a person should be able to sit on a chair with their back against the back rest of the chair whilst their feet are flat on the ground or on a footplate. Their hips, knees and ankles should be at 90-degree angles, and their arms supported by the armrests. The correct size can only be achieved if the chair is the correct seat depth and height. These two measurements are closely linked together and enable a person to sit in the chair with the ideal seated pressure distribution of:

  • Buttocks and thighs 75%
  • Feet 19%
  • Back 4%

Seat width 

When measuring the width of a person, it is important to measure the person at the widest point; for most users, this is at the hips. Keeping the tape measure straight rather than going around the abdomen is essential, as this will give you an accurate measurement of the space required between the two armrests. In some cases, the hips are not the widest point; for example, a person may have fixed abduction of the hips, making their knees the widest point. If the space between the outside of the knees and thighs is wider than the hip width, then this is the measurement that needs to be taken so that the space available will accommodate this width. When choosing the correct size chair, it's vital to consider the overall size of the user: are they an average, small, medium or large person? Then take the following 3 key measurements in this order of priority:

  • Seat depth
  • Seat height
  • Seat width

Measuring width for a riser recliner or specialist chair

When measuring the width for a riser recliner or a specialist chair, the requirements differ slightly:

Configura Rise and Recline chair

Ideally with a riser recliner, we would like to see approximately 1- 2 inches either side between the inside of the chair and the person sitting in the chair. This reduces the risk of the skin rubbing against the inside of the chair, whilst still enabling the person to reach both armrests for support when seated and when transferring. See more information about the Configura Rise and Recline chair.

Configura Advance chair

When using a specialist chair which provides postural support, the chair needs to be close fitting to provide support, enabling the user to obtain an upright position. This means the width of the chair is similar to the width of the person. All contact areas of the Configura Advance chairs, are made of a breathable, vapour-permeable fabric, which reduces the risk of pressure areas developing.

Plus-size clients 

Bariatric chair:

When measuring a plus-size client for a riser recliner, there are additional considerations. The plus-size client will have excess body mass which needs to be accommodated for and so the way we measure a plus-size client is different. The Fig. 1 below shows what is often a typical seating presentation of a plus-size client.

The extra body mass has not been accommodated for. As a result, the person has not got adequate back support and the seat height is too high. The person has tilted the chair forward to enable their feet to be in contact with the floor and their head to be in contact with the top cushion. This position places the person at risk of slipping from the chair and often requires a great deal of core strength and upper body strength to retain their position. This is uncomfortable and likely to cause pressure build up in certain areas.

Seat depth and height:

Fig. 2 shows that the actual measurement for the seat depth and seat height of a plus size user is shorter and shallower than an average sized user. This is because we need to accommodate the space required for the extra body mass under the thighs, behind the calves and behind the spine. Compare this figure with the one shown alongside seat width above, to identify the different points we measure from.

Fig. 3 shows that the lowest cushion of the waterfall backrest has been removed to accommodate the extra body mass, which is also known as the gluteal shelf. Each cushion has removable stuffing and so in some cases it is just necessary to remove part of the stuffing, rather than the whole cushion. If space for the gluteal shelf is not considered, when the person is sitting on the chair, they will not have any back support.

Seat width:

In plus-size clients, the widest part when seated is from the outside of the knees. The legs need to spread to accommodate the extra body mass around the abdomen and thighs.

Whenever a measurement is taken, it is essential to ensure that the tape measure is kept straight, as this will give you an accurate measurement of the space required between the armrests.

Details on the Configura Bariatric chair can be found here.

For more information on assessing pressure care or to book a joint assessment contact our team on 01223 206 100 or info@accora.care

Configura Advance®
Configura Advance®

Adjustable specialist seating

Our specialist seating range and can be adjusted to cater to differing size, pressure care and postural management needs.

Learn more

KottnerJ, Gefen A, Lahmann N (2011) Weight and pressure ulcer occurrence: a secondary data analysis. Int J Nurs Stud 48 (11): 2608-20

MND Association Wheelchair Pathway 2021, https://www.mndassociation.org/app/uploads/2021/01/Wheelchair-pathway.pdf

Sandoz H 2012, No pressure – a study guide. Anthony Kerr, MA Healthcare Ltd. London

Accora Team
FloorBed technology to help skilled nursing, rehabilitation and long-term care facilities prevent falls and fall-related injuries.

You might like

Postural management

What is 24-hour posture management and why it matters for OTs?

This article outlines the concept of 24-hour posture management and why it can be a valuable approach to Occupational Therapy which helps to support daily activities and occupations that improve the quality of life for their clients.

5 min read
December 5, 2023
Postural management

Postural management

In this blog, we delve into the essential considerations when assessing and selecting the right seating system for individuals with postural challenges, addressing factors like physical limitations, transfer methods, sensory needs and cognitive capacity to achieve an ideal seated posture.

6 min read
September 6, 2022
Profiling beds

What are the benefits of a FloorBed?

If you've ever wondered if a FloorBed is the right choice for you, a loved one or a service user, you're in precisely the right place to find out.

5 mins
September 6, 2023
Pressure care management

Pressure ulcer prevention and management

In this blog, we explore the critical factors contributing to pressure ulcer prevention and management in riser recliners and specialist seating systems. From assessing pressure risks related to mobility, sensation, weight and continence, to choosing the right pressure cushions and fabrics for optimal support and comfort.

5 min read
June 21, 2022

Sign up to our Newsletter

Get the best content to your inbox